Ⅱ. Operation instruction
1. Daily maintenance.
◆Check if pressure gauge indicating value is on the rated value (the finger should be in the green section. If not, you should renew inflation to return the section).
◆Check if guard strip is well, if not, you should replace a new one.
◆Check if the circle ring is locked in the safe position, that means the icon on the circle ring aims at the off position of launch bracket.

2. Launch operation.
◆Open the safety
◆One hand handles armor tube, another one screws off the circle ring safety, and also pays attention not to push the launch button when you are doing the previous action in order not to accident. When the icon on the circle ring match with triangle icon on the launch bracket, you may hear a voice that means the safety has been opened under the launch status.
◆Aiming target
In the efficient operation rang, speedy pneumatic catching net with opened safety aims at the target, Model: ZSNT02 aims at the part of head and neck of the target, Model: ZSNT01 aims at the waist of target.
◆Launching catching net
Aiming at the object, thumbs push the button by force, then a piece of umbrella-typed net with 2~3m diameter ejects from the opened safety.
◆ If the launch operation canceled but its safety has been opened or the forbid operation situation, you should return to turn off the safety (●OFF) in the counter-clockwise direction I due expedition.

3. Replace standby net
◆Dismantle belt of launched speedy air-charge catching net, screw off press lid and the part of drive, clear the drive of launch head.
◆Open standby bag and take the standby net, put it into launch head and adjust bracket to make the drive head and the hole of launch head good matched.
◆Push the launch heads one by one into launch hole. Take off bracket and circle plug, then use finger push the launch heads one by one to the bottom of launch head.
◆Ordering the down-lead of the launch head and put them into the net; put the standby guard strip into the press lid, aim at the cam of the launch head or the outer screw thread, push the press lid with guard strip or inner screw thread down, and tighten the press lid, Launch head assembled with the standby net has be finished.

4. Catching net resuming utility after launching 
◆Screw off press lid of used launch head. Stand on the table board (the bigger diameter upper).
◆ Pick up catching net, untie the launch head at the joint of down-lead an net, spread the net and clear up the sundries on the net, repeat to tie the drive head at the icon of net circumference closely one by one.
◆Drive head insert into the drive hole at the launch head in turn (Notice: it must be in turn, if not, the net would not be opened). And notice to make down-lead upper and keep a hole in the front to end of drive head
◆The left hand capture the net at the down-lead, another one settle the net and replicate the net to the left hand direction and then insert the net into launch head.
◆Take the guard strip into the press lid, and screw the lid to tighten direction, check to ensure without net outside. Now the replace net assemble finished.

5. Resume utility of power resource and inflation
◆One hand hold launch bracket, another hold armor tube and aft-lid, screw off the gas storage bottles.
◆Open the safety on the launch bracket and adjust the inner press plate, the riser should be input the slot and use the forefinger to screw the safety when you assemble the riser.
◆Clear up the mouth of dismantled gas storage bottles, use rubber plug and assemble it to the mouth. Use your left forefinger push the riser to assemble the gas storage bottles to the launch bracket. Screw close and the button of aft-lid make one line with the button of the safety.

◆Inflation method
a. Check the circle ring of assembled empty power source team in the off position. And may inflate by special inflator (please refer “inflator user guides” to know more detail). Pressure value of inflation is rated by 2.8Mpa, any change is prohibited.
b. Inflation aims at the centre hole of press lid in power source and inserts it into the bottom of rubber plug. Turn on the switch of inflation. It rubber plug. Turn on the switch of inflation. It begins inflation self-motion and the green indication light turns on.
c. The inflation will be self-motive to stop when the pressure meets the rated value. And meanwhile the green indication light turns off. Draw out the inflation needle and complete the inflation process.

◆If the remain pressure value exceeds 0.4Mpa in gas storage bottle, the daily maintenance actions is as follows: first deflate the remain gas. The method is that you put off the inflation needle from the joint the vent throat. And insert the needle and penetrate through the rubber plug and also ensure the residual gas has been removed.

Ⅲ. Operation conditions
◆Environment temperature: The product can not be used in the temperature range: -20℃~ +60℃.
◆ Humidity condition: the product has no restrict for the humidity. But the operation range will be impacted if it suffers raining or falls into water.
◆Wind power: it will have hardly influence if the wind power under the lever 2, the launch distance will be increase or decrease 0.5~1 meters/adding a wind power lever above leaver 2 when it meets free wind and dead wind respectively. The actually impact point will be deviated0.3~0.8meter/adding a wind power lever from side way. Hope the actor master the operation in the true environment.

Ⅳ. Special warm
In order to use our products rationally and ensure the safety of user and arrested target, abide by the following principles is a must in your using the products:
◆Model: ZSNT02 Operation the series to the target in 3 meters is prohibited.
◆Model: ZSNT01 Operation the serried to target in 4 meters is prohibited.
◆Safe keeping the product. Operation the products without training is prohibited.
◆ The former of products is prohibited to aim face or aim someone in close distance in order not to hurt them
◆ There has high pressure facility in the products. Any non-professional staff can not dismantle it in order not to hurt someone. If meet some defects, please send it to the expert department for resolve.
◆ The product’s life span is three years, please replace it in time.
◆ The company will not bear any concerned responsibilities if the operator do not use the product under the guides.
◆ The product is exclusive patent products, any counterfeit is prohibited, if no. the company will run its legal liability.

Ⅴ. After-sale service
◆ The product warranty card will be effective after filled and sealed by dealer.
◆ We make three promises service for our products, means we promise to withdraw if the quality defects happens in 7 days, promise to replace it in 15days, and promise to repair free in 12 months since your purchasing day.
◆ The company supply 7~24 hours after sale service, including replace net, inflation for power source, and replace product, product’s maintenance and consulting service and so on.
◆ The user should bring the effective invoice and guarantee when accepting service, the following service is out of our “three promises” service, but supply reasonable charge service:
● Exceeding the range of  “three promises”
● Without guarantee or modified guarantee card
● The destroy comes from not abiding the user manual requirement or man-made destroy situation.
● The destroy comes from being dismantle or repair at unauthorized company or by yourself.
● The destroy comes from product appearance reasonable abrasion, one-off parts.
● The destroy comes from force majeure
● The user should bear the product transportation charge.

Ⅵ. In casement list
1. Speedy pneumatic catching net  1pcs
2. User manual                              1pcs
3. Belt                                           1item
4. Qualified certification                   1pcs
5. Spear rubber plug                       1pcs
6. Spare guard strip                        1pcs
7. Spare riser                                 2pcs